[车友会] 本田爱好者进来学点好东西，给个高亮吧 [复制链接]

虾米

SkyKiwi天使

Rank: 13

升级 21.7%

UID: 37074
热情: 1438
人气: 1890
主题: 16
帖子: 8736
精华: 2
积分: 6085
阅读权限: 30
注册时间: 2002-9-6

电梯直达

楼主

发表于 2008-8-28 02:51:29 |只看该作者 |倒序浏览 微信分享

最近闹心的事情很多，睡不着，网上乱搜索，找到一个专门利用本田ECU检察电子元件问题的方法，大家好好学习学习，英文的，但是很简单，就不给翻译了，直接搬过来，希望大家喜欢

Everyone will know the CEL (Check Engine Light) that comes on briefly when you start your car while the fuel pump primes. If this light comes on while the engine is running you know you have a problem. This article will give a step by step guide to diagnosing what is wrong by doing this simple ECU check.

The ECU in most modern Hondas is located in the passenger foot well behind a plastic cover. To get to the ECU you (obviously) need to remove the cover. The cover is pictured below. It is from a DC Integra and may differ a little for other models.

The cover is held on my a few bolty screwy things that are simple to locate and remove. Go ahead and do this.

Once removed you are looking for this green silicon wire holder thing with two blue plugs inserted into it.

Now, we are only concerned with the plug to the left of that pic with one black, and one brown wire coming out of it.

The next step is to pull that plug from the green silicon thing, this can be a little fiddly but be paitent.

As you can see the plug is now turned around and two holes can be seen.

The next step is to "bridge" the two wires with a paperclip or another peice of wire such as speaker wire. Paperclips are the easiest.

As you can see the wires now form a circuit.

The next part is simple. Go round and jump in the drivers seat with the keys in the ignition. Turn the key to the "on" position. (DON'T START THE CAR) You will now see the CEL flashing randomly.

You will notice there may be long and short flashes.

A long flash = 10 and a short flash = 1.

For example... .
LONG-LONG-LONG-SHORT = 31
SHORT-SHORT-SHORT=3

The code keeps repeating until you switch the ignition off.

Here is the list of Errors and their numbers:

1 O2A - Oxygen sensor #1
2 O2B - Oxygen sensor #2
3 MAP - manifold absolute pressure sensor
4 CKP - crank position sensor
5 MAP - manifold absolute pressure sensor
6 ECT - water temperature sensor
7 TPS - throttle position sensor
8 TDC - top dead centre sensor
9 CYP - cylinder sensor
10 IAT - intake air temperature sensor
12 EGR - exhaust gas recirculation lift valve
13 BARO - atmospheric pressure sensor
14 IAC (EACV) - idle air control valve
15 Ignition output signal
16 Fuel injectors
17 VSS - speed sensor
19 Automatic transmission lockup control valve
20 Electrical load detector
21 VTEC spool solenoid valve
22 VTEC pressure valve
23 Knock sensor
30 Automatic transmission A signal
31 Automatic transmission B signal
36 traction control found on JDM ecu's
41 Primary oxygen sensor heater
43 Fuel supply system
45 Fuel system too rich or lean
48 LAF - lean air fuel sensor
54 CKF - crank fluctuation sensor
58 TDC sensor #2
61 Primary oxygen sensor
63 Secondary oxygen sensor
65 Secondary oxygen sensor heater
67 Catalyst low efficiency. (same as P0420)
70 Automatic Transmission Malfunction w/AT Controls
71 random misfire cylinder 1
72 random misfire cylinder 2
73 random misfire cylinder 3
74 random misfire cylinder 4
80 Exhaust Gas Recirculation insufficient flow detected
86 ECT Sensor (Engine Coolant Temperature) circuit range / performance problem
90 Evaporative Emission Control System leak detected in the fuel tank area
91 Evaporative Emission Control System insufficient purge flow